Category: Elegoo Saturn 3D Printer

Revell USS Arizona WWI Conversion

Revell Arizona retro 1917 refit - Blender parts
Revell Arizona retro 1917 refit - Blender parts

Since I was a teenager I’ve wanted to modify the Revell USS Arizona kit, building it in her original WW1 1916-1918 configuration. With the advent of affordable and capable 3D printers, the time has come to give it a shot!

Above are the Blender renders of the major parts I’m planing to print to pull this off. I want the new parts to blend in with the existing Revell kit, so yeah, I built me some stepped pyramid stairways, and even kept an inaccuracy in the details on the forward superfiring barbette to better match it’s stern Revell counterpart. I’ll likely need to experiment with the thickness on the individual cage mast rods. The Elegoo Saturn can print details at .05mm but I’m pretty sure if I tried printing them at that thickness the result would be a blob on the bottom of the resin vat.

Update: 6/5/2024

After initial difficulties printing the replacement deck, this project is now almost done and has (so far) come out better than I’d hoped: Revell USS Arizona WWI Conversion project page.

Joe

Graf Zeppelin 1/500 scale German recognition model complete

My Graf Zeppelin German aircraft carrier, is complete. She fits in well with the rest of the fleet. A faux WW2 recognition model, she probably has a bit more detail than a real one would’ve but I couldn’t resist, the under deck support details were just too cool to omit. She’s a whopper too, building out to about 21 inches. She was also the most difficult of my recognition replicas to design, her casemated guns were tricky and her high degree of bow flare that blends into the near vertical hanger deck sides took me a while to get right (or at least acceptable) . I actually printed a first draft on the Ender 3 that didn’t look right in hand – huge waste of filament!

I’m thinking I’ll only recreate one each of the light cruisers and destroyers that came in the original 1/500 scale German recognition set. Then I’ll call this project complete. But they’ll have to wait till spring for completion, winter has solidly set in and my resin printing is done in a shed. The Blender work will keep me busy for a bit and I’ve been off and on with a schnellboot design for almost a year…

German Admiral Scheer 1/500 scale ww2 recognition replica complete

Right on the heels of completing Scharnhorst, the design, printing, and assembly of my Admiral Scheer Pocket Battleship/Panzerschiff/Heavy Cruiser, WW2 recognition replica, was a piece of cake. Everything just came together and worked the first time.

My next design will be more challenging and diverges from the authentic 1/500 scale WW2 German recognition sets with a subject that I have always wanted to see included in them – the Graf Zeppelin Aircraft Carrier.

German battleship Scharnhorst 1/500 scale ww2 recognition replica complete

Scharnhorst is complete, I’ve been able to take advantage of a relatively warm weather window and print the resin parts for Scharnhorst, Scheer and Graf Zeppelin (GZ is actually still printing, again…). While recreating these recognition replicas has been a blast, I’m finding that without an example in hand, it’s difficult to stick to the original designs as seen from pictures on the web. I inevitably need actual pictures of the real ships to fill in the blanks and when I start designing from them, it’s painful to stop, and retain the often inaccurate design elements of the actual recognition models.

When I get all the ships completed I’ll likely make a project page to contain them all but for now this post is it for Scharnhorst.

Graf Zeppelin joins the German 1/500 scale, replica, recognition fleet

Aircraft Carrier Graf Zepplin joins the Blender recognition fleet

While waiting for a weather window to print the resin parts for Scharnhorst and Admiral Scheer I got a jump on the Graf Zeppelin’s Blender design. As was always her way, she’s not quite done yet! I did have a couple days in the low 50’s and after a totally preventable screw-up (I forgot to screw the vat down!) managed to get both their resin parts printed. The 10 day forecast says we’ll get warmish days in a week or so. With luck, I’ll get to print Graf Zeppelin’s resin before spring.

Should have Scheer and Scharnhorst built shortly. Recreating the WW2 German recognition set, has been a fun and fast project.

Update:
Links to posts for the now completed models mentioned above:
Admiral Scheer
Scharnhorst
Graf Zeppelin

Admiral Scheer German 1/500 scale recognition replica, joins my Blender fleet

The Blender work on Admiral Scheer is done, I had a good weather window to print my finished Scharnhorst design but blew it working on Scheer instead. Printing Scharnhorst will have to wait. With some luck I’ll be able to print the resin parts for both if another good day comes along.

Scharnhorst, Joins My WW2 German Fleet of Recognition Replicas in 1/500 Scale

3D Printed WW2 German recognition Fleet Replicas 1/500 Scale

Scharnhorst is almost ready to join my 3D printed WW2 German recognition replica fleet. The blender model still needs some finish work. I need to hollow out the resin parts and clip objects that are partially embedded in other parts but will be printed separately. With any luck I’ll have some warmish days to print the resin parts before the cold sets in for the season.

I don’t have an original Comet model of Scharnhorst, I searched online and used the few halfway decent pictures I could find and diagrams of the actual ship. When printed she will fill a whole in my collection nicely.

I’ll likely have plenty of time this winter to design the rest of the set. I’ll be starting the Blender design of Admiral Scheer next. I don’t have an original model of her either…

3D printed Tirpitz 1/500 scale model

October 11, 2023

After completing the Prinz Eugen replica Comet recognition model, it was only natural to follow up with Tirpitz.
Again I used the Ender 3 Pro for the “Wooden” hull parts and my Elegoo Saturn for the parts that would have been cast lead on the Comet models.

As with Prinz Eugen, the pictures with two ships show my printed model next to an original. And again like Eugen, this Tirpitz is not a perfect replica – minor improvements were made as well as a few mistakes…
My next version should be close to perfect 🙂

This was a small, simple build, so no project page, just this post.

3D printed Prinz Eugen model

August 31, 2023

After completing my 1.5 year long magnum opus called Charles Martel, I wasn’t ready for another long term commitment but I did want to putter around with something…
I remembered the 1/500 scale WWII German recognition models made by Comet and thought they’d be perfect. Here is the first: Prinz Eugen.
I also wanted to fire up the Ender 3 again and thought it would be a good fit for the “Wooden” hull parts. I used my Elegoo Saturn for the parts that would have been cast lead on the Comet models.
She’s not a perfect replica – I made some minor improvements and a couple mistakes but at less then a month from design to done – close enough!

This was a small, simple build, so no project page, just this post.

Charles Martel French Battleship, 3D printed with an Elegoo Saturn

This post introduces the Charles Martel project page. The Charles Martel was a French pre-dreadnought battleship from the end of the 19th century. Her 1/200 scale model has been by far my most ambitious 3D build, taking over a year and a half from Blender design to display case. Her project page has a ton of Elegoo Saturn print example shots, in-progress build pictures, and comments from the assembly process, below are a few images from it.